Freerchobby 60A 60V 12S 4.12 Brushless ESC Electronic Speed Controller for Electric Skateboard Drone Based Motor Controllers

FRC VESC – Open Source ESC by Benjamin's robotics

for electric skateboard 1pcs

Features

• The hardware and software is open source. Since there are plenty of CPU-resources left, the customization possibilities are almost endless.
• STM32F4 microcontroller.
• DRV8302 MOSFET driver / buck converter / current shunt amplifier.
• IRFS7530 MOEFETs (other FETs in the same package also fit).
• 5V 1A output for external electronics from the buck converter integrated on the DRV8302.
• Voltage: 8V – 60V (Safe for 3S to 12S LiPo).
• Current: Up to 240A for a couple of seconds or about 50A continuous depending on the temperature and air circulation around the PCB.
• Sensored and sensorless FOC wich auto-detection of all motor parameters is implemented since FW 2.3.
• Firmware based on ChibiOS/RT.
• PCB size: slightly less than 40mm x 60mm.
• Current and voltage measurement on all phases.
• Regenerative braking.
• DC motors are also supported.
• Sensored or sensorless operation.
• A GUI with lots of configuration parameters
• Adaptive PWM frequency to get as good ADC measurements as possible.
• RPM-based phase advance (or timing/field weakening).
• Good start-up torque in the sensorless mode (and obviously in the sensored mode as well).
• The motor is used as a tachometer, which is good for odometry on modified RC cars.
• Duty-cycle control, speed control or current control.
• Seamless 4-quadrant operation.
• Interface to control the motor: PPM signal (RC servo), analog, UART, I2C, USB or CAN-bus.
• Wireless wii nunchuk (Nyko Kama) control through the I2C port. This is convenient for electric skateboards.
• Consumed and regenerated amp-hour and watt-hour counting.
• Optional PPM signal output. Useful when e.g. controlling an RC car from a raspberry pi or an android device.
• The USB port uses the modem profile, so an Android device can be connected to the motor controller without rooting. Because of the servo output, the odometry and the extra ADC inputs (that can be used for sensors), this is perfect for modifying an RC car to be controlled from Android (or raspberry pi).
• Adjustable protection against
  • Low input voltage
  • High input voltage
  • High motor current
  • High input current
  • High regenerative braking current (separate limits for the motor and the input)
  • Rapid duty cycle changes (ramping)
  • High RPM (separate limits for each direction).
• When the current limits are hit, a soft back-off strategy is used while the motor keeps running. If the current becomes way too high, the motor is switched off completely.
• The RPM limit also has a soft back-off strategy.
• Commutation works perfectly even when the speed of the motor changes rapidly. This is due to the fact that the magnetic flux is integrated after the zero crossing instead of adding a delay based on the previous speed.
• When the motor is rotating while the controller is off, the commutations and the direction are tracked. The duty-cycle to get the same speed is also calculated. This is to get a smooth start when the motor is already spinning.
• All of the hardware is ready for sensorless field-oriented control (FOC)

Company information:

Dongguan Freerchobby Co.,Limited is a private-owned enterprise, located in Dongguan, which is famous for the world factory with highly developed economy. The company has 1500 square meters of modern industrial plants and advanced assembly line equipment. We are specialized in manufacturing brushless dc motor, controller, model parts, hardware parts and so on. The company has 10 CNC lathes, 5 BLDCM winders and various advanced automatic processing equipment. Our company has a very stable supply capacity, monthly production more than 15000 sets of brushless motor and motor and controller accessories as well as hardware accessories 100000. The products sell well in more than 50 countries and regions from the whole world.

The company strictly controls each process to be standardization, systematization and unification. The company has testing equipment such as dynamic balancing machine, comprehensive tester for BLDCM, noise tester, Gauss tester, tension tester, oscilloscope, etc. to test the performance of motor and controller in a full range and ensure that each performance index can reach the international leading level. All products and parts are in line with ROHS standards, and have won CE and ROHS certification.

The company adheres to the tenet of "quality first, reputation first and service superior", improves the brand awareness, gives full play to the brand advantages, maintains the brand image, and provides the most reliable quality, the best service and the fastest delivery for customers at home and abroad with exquisite technology and standardized management.

Our slogan is "we can do what you need"! We are looking forward to cooperating with you!

Packaging

Certificate:

Why choose Freerchobby?

1, Strong after sale service:

All products will be 180days quality guarantee free of charge, and additional repair can be guarantee in 2 years if goods can be return.

2, OEM&ODM sercice

Freerchobby is the factory, we can provide all service from design to production. Lots of CNC machine and auto lathes and many production line in our factory.

3, About the shipment:

All the standard goods will be shipped within 3-4days. If OEM projects, we will discuss shipment sepratively. All the goods will be in safe packaging and marked with handle with care. And shipment will be taken by fastest express, DHL, TNT, FEDEX, UPS.

4, About the feedbacks

Freerchobby will listen to any suggestion for improving our product quality and service, just feel free to contact us

5, About the discount

Any customer who give us 5 start comments, we will give you 5% discount when you purchase next time